Laxmi En-fab Private Limited

Air Classification is the process of separating particles according to the settling velocity in a gas. Air Classifiers are used to separate dry materials into different particle size fractions by their size, mass or shape. Air Classifiers are used to modify a particle size distribution, remove the fines fraction of a material or the oversize or coarse particles of a material or create two grades of material.

In event of air classification cycle of operation, material enters the center feed pipe and drops upon the rotating distributor plate below, which disperses the material into the upward sweep of circulating air developed by the fan in the top chamber of the drum. The Whizzer blades set up a centrifugal motion of the air and material. This concentrates the oversize material along the surface of the upper inner cone, where gravity causes it to flow into the lower inner cone and then out the tailings spout at the bottom. The air stream carrying the powdered material of required fineness moves through the fan and is delivered into the outer cone chamber where the fines are discharged as a finished product which is desired to classify. After the fines are released in the outer cone, the air returns through the deflector ports to the inner cone, setting up a continuous cycle.

Air Classifiers are Ideal for Pigment Colours - Minerals & Ores - Chemicals Technical Products Dyestuffs - Fertilizer - Insecticides - Pesticides.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)

We are one of the leading suppliers of Fly ash classifier in india.

Features:

• Less power consumption
• Optimum performance
• dimensional stability

Features:

• Less power consumption
• Optimum performance
• dimensional stability

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Production Capacity: 10 TPH
• Delivery Time: 1 month

Air Classification is the process of separating particles according to the settling velocity in a gas. Air Classifiers are used to separate dry materials into different particle size fractions by their size, mass or shape. Air Classifiers are used to modify a particle size distribution, remove the fines fraction of a material or the over size or coarse particles of a material or create two grades of material.

In event of air classification cycle of operation, material enters the centre feed pipe and drops upon the rotating distributor plate below, which disperses the material into the upward sweep of circulating air developed by the fan in the top chamber of the drum. The whizzer blades set up a centrifugal motion of the air and material. This concentrates the oversize material along the surface of the upper inner cone, where gravity causes it to flow into the lower inner cone and then out the tailings spout at the bottom. The air stream carrying the powdered material of required fineness moves through the fan and is delivered into the outer cone chamber where the fines are discharged as finished product which is desired to classify. After the fines are released in the outer cone, the air returns through the deflector ports to the inner cone, setting up a continuous cycle.

Air Classifiers are Ideal for Pigment Colours - Minerals & Ores - Chemicals Technical Products Dyestuffs - Fertilizer - Insecticides - Pesticides.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)

Air Classification is the process of separating particles according to the settling velocity in a gas. Air Classifiers are used to separate dry materials into different particle size fractions by their size, mass or shape. Air Classifiers are used to modify a particle size distribution, remove the fines fraction of a material or the over size or coarse particles of a material or create two grades of material.

In event of air classification cycle of operation, material enters the centre feed pipe and drops upon the rotating distributor plate below, which disperses the material into the upward sweep of circulating air developed by the fan in the top chamber of the drum. The whizzer blades set up a centrifugal motion of the air and material. This concentrates the oversize material along the surface of the upper inner cone, where gravity causes it to flow into the lower inner cone and then out the tailings spout at the bottom. The air stream carrying the powdered material of required fineness moves through the fan and is delivered into the outer cone chamber where the fines are discharged as finished product which is desired to classify. After the fines are released in the outer cone, the air returns through the deflector ports to the inner cone, setting up a continuous cycle.

Additional Information:

• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),Other

We are leading manufacturer, supplier and exporter of Classification equipment like Air classifier, Air classifier system, Air separating system, Air Separator, Air Classifier Mill, Fly Ash Classification System, Air jet mill, classifier mill, Air classifier air separator,Air Classification System.

Ideal For

• Pigment Colors - Minerals & Ores - Chemicals Technical Products Dyestuffs - Fertilizer - Insecticides - Pesticides.

• Particle size is finer and more uniform than

Laxmi En Fab Air classifier Features :
1. Strong construction of mechanism and casing ensures long life

2. Close control over product uniformity

3. Special liners are available for processing abrasive materials.

4. Particles are reduced to finer and more uniform sizes.

5. Use of cyclone separator lead to less dusting on output side

6. No dusting from feeding hopper because feeding is done under negative pressure

7. It runs at lower speed, hence it requires much less maintenance that obtained from machine using screen

• No dusting from feeding hopper because feeding is done under negative pressure.
• Less dusting on output side because of use of cyclone separator.
• It uses air-classification witch does require screen , Hence the problems associated with screen like choking, painting and frequent replacement of screen do not arise.
• Easy to clean and wash.
• It is manually fed as a normal practice. However, it can be supplied with automatic feeding also
• It runs at low speed compared to machines using screen, hence much lass maintenance

This classification equipment that finds extensive use in research laboratories. Used for achieving uniform drying of material within a fraction seconds, this machine is highly demanded by our clients based in domestic market. Laxmi En Fab is leading manufacturers of Industrial classifier in Ahmedabad, Manufacturer of air classifier in ahmedabad and supply this classifier in different city of Gujarat, Rajasthan, Maharashtra, Bangalore, Chhatishgath, Punjab, Karnataka, Assam, Haryana, Tamilnadu, Kolkatta, Madhya Pradesh, like Faridabad, Bhavnagar, Ankleshwar, Vadodara, Baroda, Kadi, Surat, Mumbai, Pune, Tane, Silvasaa, Chandrapur, Rangareddy, Siddipet, Ratanagiri, Siddipet, Ratanagiri, Raigad, Bhopal, Sircilla, Cuddalore and different city in India and also export this classification system in developing country

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Delivery Time: 3 month

We are leading manufacturer, supplier and exporter of Classification equipment like Air classifier, Air classifier system, Air separating system, Air Separator, Air Classifier Mill, Fly Ash Classification System, Air jet mill, classifier mill, Air classifier air separator,Air Classification System.

Ideal For

• Pigment Colors - Minerals & Ores - Chemicals Technical Products Dyestuffs - Fertilizer - Insecticides - Pesticides.

• Particle size is finer and more uniform than 

Laxmi En Fab Air classifier Features:
1. Strong construction of mechanism and casing ensures long life

2. Close control over product uniformity

3. Special liners are available for processing abrasive materials.

4. Particles are reduced to finer and more uniform sizes.

5. Use of cyclone separator lead to less dusting on output side

6. No dusting from feeding hopper because feeding is done under negative pressure

7. It runs at lower speed, hence it requires much less maintenance that obtained from machine using screen

• No dusting from feeding hopper because feeding is done under negative pressure.
• Less dusting on output side because of use of cyclone separator.
• It uses air-classification witch does require screen , Hence the problems associated with screen like choking, painting and frequent replacement of screen do not arise.
• Easy to clean and wash.
• It is manually fed as a normal practice. However, it can be supplied with automatic feeding also
• It runs at low speed compared to machines using screen, hence much lass maintenance

This classification equipment that finds extensive use in research laboratories. Used for achieving uniform drying of material within a fraction seconds, this machine is highly demanded by our clients based in domestic market. Laxmi En Fab is leading manufacturers of Industrial classifier in Ahmedabad, Manufacturer of air classifier in ahmedabad and supply this classifier in different city of Gujarat, Rajasthan, Maharashtra, Bangalore, Chhatishgath, Punjab, Karnataka, Assam, Haryana, Tamilnadu, Kolkatta, Madhya Pradesh, like Faridabad, Bhavnagar, Ankleshwar, Vadodara, Baroda, Kadi, Surat, Mumbai, Pune, Tane, Silvasaa, Chandrapur, Rangareddy, Siddipet, Ratanagiri, Siddipet, Ratanagiri, Raigad, Bhopal, Sircilla, Cuddalore and different city in India and also export this classification system in developing country

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)